当前位置:首页 > support > ICHIB-C1-En > 正文内容

Batch modification of firmware information -[Delete, Replace, Add]

Log in to ICHIB-C1- click "Inc Dec "in" Toolkits "to operate in the dialog box that pops up.(After Delete,  Replace,  Adding, the corresponding folder will be generated in the "ICHIB-C1\BinTools\" directory)

Function Introduction:

1 Open: you can prepare some files as common data (file format txt)

2 Save: Save the contents in the edit box to a txt file

3 Clear Data: Clear data in the edit box with one click

4 Calculate characters: Calculate the length of the characters in the edit box

---------------------------------------------

5 Adding: Add firmware characters (binary bin format files, multiple files are supported)

6 Delete: Delete firmware characters (binary bin format files, multiple files are supported)

7 Replace: Replace firmware characters (binary bin format file, support multiple files, support checksum calculation)

1.png

5, Adding: Drag and drop the firmware folder to the red box on the window. Fill in the edit box to add the character content, it is recommended to calculate the character first to avoid errors. From "Start Add" set the address from which to add characters (if you fill in 0 then start adding before the first character, if you fill in 1 then start adding after the first character, be careful to back up the original file before use)


6, Delete: Drag and drop the code folder to the red box on the window. From "Start Add" set the address from which to delete all characters after (if you fill in 0 then delete all, if you fill in 1 then delete everything after the first character, be careful to back up the original file before use)


7, Replace: Drag and drop the code folder to the red box on the window. Fill in the edit box to replace the character content, it is recommended to calculate the character first to avoid errors. From Starting Position sets the address from which to start replacing characters. (If you fill in 0, then the first byte starts to replace, if you fill in 1, then the replacement starts from the second character, pay attention to backup the original file before use) If necessary, you can "check 3F and 5F after replacement". (GBIC,SFP,XFP,QSFP corresponding areas have this function requirement)

扫描二维码推送至手机访问。

版权声明:本文由IICHIB发布,如需转载请注明出处。

本文链接:http://ichib.com/post/85.html

分享给朋友:

“Batch modification of firmware information -[Delete, Replace, Add]” 的相关文章

XFP optical module Read Digital Diagnostic Monitoring(DDM/DOM)

XFP optical module Read Digital Diagnostic Monitoring(DDM/DOM)

The hardware device in this demonstration is 10G-XFP-SRAll XFP packaged fiber modules can be used for referencePrepare multi-mode optical fiber module...

Verify - Compare written firmware for correctness and completeness

Verify - Compare written firmware for correctness and completeness

This function is applicable to all firmware writing.Check "Verify" in the write option when writingUse this feature in unknown or uncertain...

SFP optical transceiver reads the firmware

SFP optical transceiver reads the firmware

The hardware device in this demonstration is 1.25G-SFP-SXAll SFP packaged fiber modules can be used for referenceAfter the software opens, log in.Perf...

QSFP-DD optical transceiver reads the firmware

QSFP-DD optical transceiver reads the firmware

The hardware device in this demonstration is 400G-QSFP-DD-DF4All QSFP-DD packaged fiber modules can be used for referenceAfter the software opens, log...

"Configuration" Details ICHIB-C1

"Configuration" Details ICHIB-C1

This setting is explained in two parts :" Read and write"1, the parameter used when reading1:page size(The SFF protocol requires the value t...

SFP optical module Read Digital Diagnostic Monitoring(DDM/DOM)

SFP optical module Read Digital Diagnostic Monitoring(DDM/DOM)

The hardware device in this demonstration is 1.25G-SFP-SXAll SFP packaged fiber modules can be used for referencePrepare multi-mode optical fiber modu...